|
|
Tap on this icon to save your
changes to the Database |
 |
Tap on this
icon to abort disregarding your changes
|
 |
Tap on this
icon to open an Image to be used as the Yardage Book Image of the
Hole. You can select in the Window coming up between GIF, JPEG
and BMP Images |
 |
Tap on this
icon to remove the Image from the Holes Yardage Book. Warning:
when removing the image, you remove all the Notes on the Image
and the calibration of the image. |
 |
Tap on this
icon to rotate the image 90 degrees clockwise |
 |
Tap on this
icon to rotate the image 90 degrees counterclockwise |
 |
Tap on this
icon to mirror the image horizontally |
 |
Tap on this
icon to mirror the image vertically |
 |
Tap on this
icon to zoom into the Image |
 |
Tap on this
icon to zoom out of the Image |
 |
Tap on this
icon to zoom the Image in such a way that the entire Image is
visible on the Screen |
 |
Tap on this
icon to zoom the Image in such a way that the Image is Shown in
its original Pixel Size |
 |
Tap on this
icon to switch to the Note-Adding mode. Once switch to that
mode, you can double-click with your Stylus on any place of
the Image to add a note. In the Window coming up, you can type
your note. You can use the three Drop-Downs to add standard
Words for the Club used, the Length and the Landing to the note.
Tap OK to save the Note or Cancel to
not add the note. Once a Note is added, you see a little Note
Icon at the Spot where you added the note. Double-click on this
Icon to open, see or edit the Note. When the Note is open for
editing, you can tap on OK to save the edits or Delete
to delete the Note. |
 |
Tap on this
icon to visualize Distance Marks for 100, 150 and 200
Yards on Top of the Image. For these Marks to appear, the
Position of the Start of the Green must be defined and the Image
must be calibrated either graphically or by GPS.
When the Marks are shown, you can double-click with your Stylus
on any place of the Image to cause the marks to show the
Distances to the Point you double clicked at. To set the new
center, answer Yes to the question that comes up, if you
want the center to stay at the Start of the Green, tap on No.
To remove the
Marks, tap again on the Icon. |
 |
Tap on this Icon to Calibrate
the Image graphically by setting the Image Scale. You calibrate the
image by selecting a line you know the Distance on the Image of
and then enter the length of the Distance in the selected
units. After tapping you get
a little Dialog with some Instructions. After closing this
dialog with OK, you must tap on the first position
of the Line. Keep your Stylus pressed and move it towards the
second Position. The Image will scroll while you move the
Stylus. Finally, tap on the second Position of the Line.
Then, a Dialog pops up in which you must enter the Distance of
the Line. By activating 2nd Point is Start of Green the
second Point of your Line will be set as the Position of the
Start of the Green. There, tap on OK to calibrate your image or Cancel. |
 |
In case the
Image was
GPS calibrated and the Setting to use GPS rather than
graphical Calibration is activated, the GPS Ruler is shown
instead of the Ruler. Using this Icon, you can measure a
Length on the Image. To do so, select a line as described
above. After selection, you can see the Length of the Line in a
window that can be closed with OK. |
 |
Tap on this
icon to set the Position of the Start of the Green. After tapping you get a
little Dialog with some Instructions. After closing this dialog
with OK, you can scroll and zoom in the Image to see the
Position of the Start of the Green. Then, tap on that position and you
are done. |
 |
Tap on this icon to perform the
GPS calibration for the Yardage Book Image. |
 |
Tap on this icon to cut out the
Hole Image. Do do that, you must draw a Polygon around the
part of the Image you want to keep. Click on the first point of
the Polygon and then on the additional Points. The Polygon is
shown with a small line. To cut out the Image, double-click on
the last Point of the Polygon. To abort the cutting, click
outside of the Image. This Icon is only available when you
opened the Yardage Book from the
Edit Tee Screen. |
 |
Tap on this icon to visually
record the Ball Landings on the Yardage Book Image. This Icon is
only available when you opened the Yardage Book from the Playing the Game
Screen. |
 |
Tap on this icon to visualize
your Standpoint using GPS on the Yardage Book Image.
If activated in the
Preferences, the Hole Image will be always centered to your
Standpoint. |
 |
Tap on this icon to toggle your Screen orientation
between Portrait and Landscape. This in only possible on Devices
running Windows Mobile 2003 SE and supporting this
functionality. |
 |
Tap on this icon to switch between
seeing all Icons or just the most important ones, the latter
giving more screen space to the Image itself. This Icon is
only available when you opened the Yardage Book from the Playing the Game
Screen.
|
 |
Tap on this icon to go back one
Hole. This Icon is only available when you opened the Yardage
Book from editing a Tee or
from Round Statistics - Review. |
 |
Tap on this icon to go forward one
Hole. This Icon is only available when you opened the Yardage
Book from editing a Tee or
from Round Statistics - Review. |
|
|
If activated in the
Preferences, all changes
made can be saved automatically when you use on of these two
Icons to navigate through the Hole Images. |